Underwriters Laboratories Network IR Speed Dome Camera Manual de instalación Pagina 1

IR Speed Dome Installation Manual V2.0.0

IR Speed Dome Installation Manual 9 Figure. 1.2.7 Bottom board of network IR speed dome 1. Address DIP Switch 2. Protocol DIP Switch

IR Speed Dome Installation Manual 10 Figure. 1.2.8 Bottom board of network high-definition IR speed dome 1. Terminal Resistance DIP Switch 2.

IR Speed Dome Installation Manual 11 4. Cover the sealing ring and tie the safety lanyard to the dome. Note: The sealing ring must be set for the d

IR Speed Dome Installation Manual 12 Figure. 1.2.11 Hang the dome to the top cover Figure. 1.2.12 Bottom circuit board (IR speed dome) 1.

IR Speed Dome Installation Manual 13 Figure. 1.2.13 Bottom circuit board (network IR speed dome) Figure. 1.2.14 Bottom circuit board (network h

IR Speed Dome Installation Manual 14 Figure. 1.2.10 Fix the IR Speed Dome 1.3 Initial Settings Address code: 0 Baud rate: 2400 120Ω matched res

IR Speed Dome Installation Manual 15 1.4 DIP Switch Settings Note: The parameters of 485 serial port of network high-definition IR speed dome mus

IR Speed Dome Installation Manual 16 DIP switch settings needed for setting control protocol. Note: If the dome is subject to electromagnetic inter

IR Speed Dome Installation Manual 17 27 ON ON OFF ON ON OFF OFF OFF 28 OFF OFF ON ON ON OFF OFF OFF 29 ON OFF ON ON ON OFF O

IR Speed Dome Installation Manual 18 71 ON ON ON OFF OFF OFF ON OFF

IR Speed Dome Installation Manual 1 Thank you for purchasing our product. If there are any questions, or requests, please do not hesitate to contac

IR Speed Dome Installation Manual 19 1.4.3 Baud Rate Settings The positions 1-3 of the DIP Switch SW2 are used for setting the baud rate of the

IR Speed Dome Installation Manual 20 1.5 Alarm In/Out Connections The IR speed dome, network IR speed dome can be connected with 7 alarm inputs (0~

IR Speed Dome Installation Manual 21 Chapter 2 Mounts Dimension 2.1 Long Wall Mount Unit: mm Wall mount with power supply box

IR Speed Dome Installation Manual 22 2.2 Short Wall Mount 2.3 Corner Mount

IR Speed Dome Installation Manual 23 2.4 Pole Mount

IR Speed Dome Installation Manual 24 Chapter 3 Wall Mounting Applications 3.1 Mounting Components  Wall Mount Wall mounts are applicable to ind

IR Speed Dome Installation Manual 25 Step1: Drill mounting holes in the wall and install the expansion screws Drill four holes in the wall accordi

IR Speed Dome Installation Manual 26 Step3: Install dome to the mount Pass cables through the opening on top of the back box, screw the pipe threa

IR Speed Dome Installation Manual 27 Step3: Install dome to the mount Note: Follow the same instructions described above for the Short Mount in

IR Speed Dome Installation Manual 28 Chapter 4 Corner Mounting Applications 4.1 Mounting Components  Wall Mount Wall mount is applicable to t

IR Speed Dome Installation Manual 2 Safety Instruction These instructions are intended to ensure that the user can use the product correctly to avo

IR Speed Dome Installation Manual 29 4.2 Corner Mounting Instructions The corner mounting is applicable to the indoor/outdoor 90° solid corner cons

IR Speed Dome Installation Manual 30 Step3: Install dome to the mount Pass cables through the opening on top of the back box, screw the pipe threa

IR Speed Dome Installation Manual 31 Chapter 5 Pole Mounting Applications 5.1 Mounting Components  Wall Mount Wall mount is applicable to the i

IR Speed Dome Installation Manual 32 Pole mount hoop is used to cooperate with pole mount, with following dimensions selectable: φ59-82mm, φ84-108m

IR Speed Dome Installation Manual 33 Step2: Install pole mount Pull the power cord, video cable and control line through the opening of the pole

IR Speed Dome Installation Manual 34 Step4: Install dome to the mount Pass cables through the opening on top of the back box, screw the pipe threa

IR Speed Dome Installation Manual 35 Appendix 1 Lightning & Surge Protection This product adopts TVS plate lightning protection technology to

IR Speed Dome Installation Manual 36 Appendix 2 RS485 Bus Connection 1. General Property of RS485 Bus According to RS485 industry bus standard, R

IR Speed Dome Installation Manual 37 switch off the eighth bit of SW2, it will be unconnected. Figure 3 4. Problems in the Practical Applicat

IR Speed Dome Installation Manual 38 Figure 4 For such case, the best way is adding a RS485 distributor. This product can effectively change the s

IR Speed Dome Installation Manual 3 Preparation for Installation 1. Basic requirements 1) All the electronic operation should be strict complianc

IR Speed Dome Installation Manual 39 Appendix 3 Table of Wire Gauge Standards

IR Speed Dome Installation Manual 4 Table of Contents Chapter 1 Installation ...

IR Speed Dome Installation Manual 5 Chapter 1 Installation 1.1 Check Parts List Prior to installation, unpack the dome unit and check whether it

IR Speed Dome Installation Manual 6 Figure 1.2.2 Install the fast mounting adapter (3) Befor

IR Speed Dome Installation Manual 7 Figure 1.2.4 Screw up the lock screws 3. Take out the speed dome and tear off the protective sticker from it,

IR Speed Dome Installation Manual 8 Figure. 1.2.6 Bottom board of IR speed dome 1 2 3 1. Address DIP Switch 2. Protocol DIP Switch 3. Add